Primos Yo Sista & Other Call Tuning- ★HELP★

[DuckFuller]

I have seen quite a few of you guys also carry a "yo sista"... how do u clean it, & tune it? Qtips and h20 or alcohol? Anyone know a way to keep double reeds from sticking and making that god forsaken sqreechh! Onbthe spit tech/zink and B.Gardner I have no problem. The Duck Commander & Primos, Yes!
Also what about ports for loudness? Is it a DIY modification or for a Call maker?
*YOUR ANSWERS ARE ALWAYS HELPFUL, AND I APPRECIATE THEM*

[The Duck Hammer]

If the call is a J Frame take the call apart, pull the reed and cork out, and soak it in warm soapy water. I wouldn't use alcohol as it with crack acrylic, don't know what it will do to poly but the warm water works fine. I have used qtips on my calls when there is stuff in the tone channel like food or dirt. The only thing I know of that might help you out on the sticking is if you bend the top reed up slightly to widen the gap between the two reeds. The reason doubles do what you are talking about is because spit gets between the two reeds and forms a vacuum that seals the reeds together and the only way to break it is by blowing on it hard. That's one of the reasons I sold my doubles. There is a sticky on this forum right above where this post will be that is the best way to tune a call out there for someone who doesn't know what they are doing.

[assateague]

I've also found that after each time I call, just spin the call around and blow once through the opposite end. That keeps them from sticking and freezing very well, if you remember to do it.

[Tiler_J]

You can run a dollar bill between the reeds or the edge of your shirt if you are gentle to clean the spit from between the reeds while hunting, if it gets jammed up.

[The Duck Hammer]

You can run a dollar bill between the reeds or the edge of your shirt if you are gentle to clean the spit from between the reeds while hunting, if it gets jammed up.

I've tried that and it was always 50/50 for me.

[DuckFuller]

I contacted primos and the yo sista does come apart. They said it may have to be literally pried or hammered to get open. Its not bad and the cork looks great, however I have a poly Duck commander 'Ol Raspy' and I cannot get it to tune rite. The reeds are fine and sound board is fine, as the wedge. But it just doesn't sound rite. I talked to Justin Martin @ Duck commander and he said I may need a replacement or reeds but the ones in the Camo max are identical, I swapped them and used some rnt reeds in it and it just makes a bad sound... any suggestions fellas?

[Tiler_J]

You can run a dollar bill between the reeds or the edge of your shirt if you are gentle to clean the spit from between the reeds while hunting, if it gets jammed up.

I've tried that and it was always 50/50 for me.

So you agree, it works! Haha! It's not the best, but when you got nothing else while hunting it works pretty good for me.

[The Duck Hammer]

I have nothing good to say about modern DC calls except the specialty calls. Because of the way the reeds are produced its damn near impossible to do anything with them. The only safer way to tune them is to trim the reed from the back don't try and mess with the front. Of the DC calls I have the main problem I have had with them is with the wedge. Their wedge sizes are very inconsistent and some pin a lot of the reed down others not so much.

[The Duck Hammer]

You can run a dollar bill between the reeds or the edge of your shirt if you are gentle to clean the spit from between the reeds while hunting, if it gets jammed up.

I've tried that and it was always 50/50 for me.

So you agree, it works! Haha! It's not the best, but when you got nothing else while hunting it works pretty good for me.

Yep it works sometimes. But IMO its not worth my time messing with them.

[Feelin' Fowl]

I contacted primos and the yo sista does come apart. They said it may have to be literally pried or hammered to get open. Its not bad and the cork looks great, however I have a poly Duck commander 'Ol Raspy' and I cannot get it to tune rite. The reeds are fine and sound board is fine, as the wedge. But it just doesn't sound rite. I talked to Justin Martin @ Duck commander and he said I may need a replacement or reeds but the ones in the Camo max are identical, I swapped them and used some rnt reeds in it and it just makes a bad sound... any suggestions fellas?

I would send it in if that's an option. Let them fix it, or replace it...

[RonE]

:duck: I have seen quite a few of you guys also carry a "yo sista"... how do u clean it, & tune it?

Get "yo momma" to clean it fo you.

[rebelp74]

:duck: I have seen quite a few of you guys also carry a "yo sista"... how do u clean it, & tune it?

Get "yo momma" to clean it fo you.

Ha!

[Goldfish]

Make sure the reeds are not upside down. I did that to my microhen and couldn't figure out why my magic call all of a sudden sounded like shit. Got them turned the right way, and it was back to beautiful.

sent from a phancy fone

[RonE]

You can run a dollar bill between the reeds or the edge of your shirt if you are gentle to clean the spit from between the reeds while hunting, if it gets jammed up.

I didn't have a dollar bill so I used three quarters, two dimes and a nickel an now the call ain't worth a darn.

[Redbeard]

You can run a dollar bill between the reeds or the edge of your shirt if you are gentle to clean the spit from between the reeds while hunting, if it gets jammed up.

I didn't have a dollar bill so I used three quarters, two dimes and a nickel an now the call ain't worth a darn.

so much for black bear diner

[aunt betty]

Make sure the reeds are not upside down. I did that to my microhen and couldn't figure out why my magic call all of a sudden sounded like shit. Got them turned the right way, and it was back to beautiful.

sent from a phancy fone

I was thinking the same thing..
To find which side goes up...
Place reed between thumb and finger like this.

Squeeze and it does this.

It will go up or down.
Milar comes in huge rolls so the reed has memory.

[aunt betty]

When you put it in your call...a smiling reed is a happy reed.
The bowed part goes down.

[aunt betty]

If I were to put the reed into that insert it would go like that. Smile!